Your Plumbing Crash Course: A Necessity for Bathtub Installation
Your Plumbing Crash Course: A Necessity for Bathtub Installation
Blog Article
Just how do you really feel with regards to How to Install a Bathtub: Install an Acrylic Tub and Tub Surround?
Setting up a bathtub isn't exactly brain surgery, yet it does need strong plumbing, carpentry, and also often, tiling abilities. Changing an old tub with a brand-new one is likewise a reasonably tough job. If the old bathtub is easily easily accessible, the job can relocate easily; if you have to open up a wall surface to get rid of the old tub and place the brand-new bathtub, the task is a lot harder. In either case, the task is within a residence handyman's skills, although you will certainly need a helper to leave the old tub as well as set in the brand-new one. See to it you have certified yourself for the work and fit trying it. Rather than working with a service provider to take control of a halfway-completed project, it is far better to think about using one before you begin. Chances are you might need a specialist plumber to make tube connections.
This article will aid you set up a brand-new tub in your washroom if you have actually currently purchased a new tub and also don't require to alter the setup of your previous supply of water pipes.
Your tools and also material checklist should comprise the following:
Preparing for the Setup
Firstly, the supporting structure provided with the bath should be fitted (if needed) according to the manufacturer's directions. Next, fit the taps or mixer to the bathtub. When fitting the faucet block, it is essential to make certain that if the tap comes with a plastic washing machine, it is fitted in between the bath and the taps. On a plastic bath, it is likewise sensible to fit a supporting plate under the faucets device to stop strain on the tub.
Fit the flexible tap adapters to the bottom of both taps making use of 2 nuts as well as olives (in some cases supplied with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet hole, and afterwards pass the outlet with the hole in the bathroom. Utilize the nut supplied by the maker to fit the plug-hole. Take a look at the plug-hole outlet for an inlet on the side for the overflow pipe.
Next, fit the end of the flexible overflow pipe to the overflow electrical outlet. After that, screw the pipe to the overflow face which need to be fitted inside the bathroom. Make sure you use all of the provided washing machines.
Link the trap to the bottom of the waste electrical outlet on the bath tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, as well as screw on the trap to the outlet. Connect all-time low of the overflow tube in a similar manner.The bathroom must currently be ready to be suited its final setting.
Removing Old Taps
If you require to replace old faucets with brand-new ones as a part of your installment, then the first thing you ought to do is detach the supply of water. After doing so, activate the taps to drain pipes any kind of water staying in the system. The process of getting rid of the existing faucets can be rather troublesome due to the limited accessibility that is usually the situation.
Utilize a basin wrench (crowsfoot spanner) or a tap tool to undo the nut that connects the supply pipelines to the taps. Have a towel all set for the staying water that will certainly come from the pipes. When the supply pipelines have been removed, make use of the same tool to loosen the nut that holds the taps onto the bath/basin. You will need to quit the solitary faucets from turning throughout this process. When the taps have actually been removed, the holes in the bath/basin will certainly have to be cleaned up of any old sealing substance.
Before going on to fit the new taps, contrast the pipeline connections on the old taps to the brand-new faucets. If the old faucets are longer than the new taps, then a shank adapter is needed for the brand-new faucets to fit.
Installing the Bathtub
Using both wood boards under its feet, position the bathtub in the needed setting. The wood boards are helpful in evenly spreading the weight of the bathtub over the location of the boards rather than concentrating all the weight onto 4 little points.
The next goal is to ensure that the bath tub is leveled all round. This can be attained by examining the spirit level as well as changing the feet on the tub up until the level checks out degree.
To set up taps, fit the bottom of the outermost adaptable tap port to the appropriate supply pipe by making a compression join; after that do the exact same for the various other faucet.
Switch on the supply of water and also examine all joints and also brand-new pipework for leaks and tighten them if necessary. Fill the tub and also inspect the overflow outlet and the regular electrical outlet for leakages.
Ultimately, repair the bath paneling as defined in the maker's user's manual. Tiling and sealing around the tub needs to wait until the bathtub has been utilized at the very least once as this will certainly resolve it right into its last placement.
Suitable New Touches
If the tails of the brand-new faucets are plastic, after that you will certainly require a plastic port to avoid damage to the thread. One end of the connector fits on the plastic tail of the faucet as well as the other end offers a connection to the current supply pipes.
If you need to fit a monobloc, after that you will certainly require reducing couplers, which connects the 10mm pipeline of the monobloc to the common 15mm supply pipeline.
Next off, place the tap in the mounting hole in the bath/basin guaranteeing that the washing machines are in place between the tap and also the sink. Safeguard the faucet in place with the producer given backnut. Once the tap is firmly in position, the supply pipelines can be connected to the tails of the faucets. The faucets can either be connected by using corrugated copper piping or with normal tap adapters. The previous type ought to be attached to the tap ends first, tightening up just by hand. The supply pipelines can later be connected to the other end. Tighten up both ends with a spanner after both ends have actually been attached.
Tiling Around the Bathtub
In the area where the bath satisfies the ceramic tile, it is essential to secure the accompanies a silicone rubber caulking. This is essential as the fitting can move enough to break an inflexible seal, causing the water to permeate the wall surface between the bath and also the tiling, causing problems with moisture and also feasible leakages to the ceiling below.
You can pick from a range of coloured sealers to assimilate your components and fittings. They are sold in tubes as well as cartridges, and also are capable of securing voids as much as a width of 3mm (1/8 inch). If you have a larger space to fill, you can load it with spins of soaked newspaper or soft rope. Keep in mind to constantly load the bath tub with water prior to sealing, to enable the movement experienced when the bathtub is in use. The sealant can break fairly early if you do not take into account this motion prior to securing.
Alternatively, ceramic coving or quadrant ceramic tiles can be made use of to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and cut to size, are also quickly offered on the marketplace. It is suggested to fit the floor tiles using water-resistant or waterproof adhesive and grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
I'm very interested by A Step-by-Step Guide to Installing a Bathtub and I really hope you enjoyed reading my post. If you please take a moment to promote this post if you enjoyed it. Thank-you for going through it.
We're your answer! Report this page